Once it's ready, open your browser and go to 192.168.1.1 to open LuCi interface. It may take up to 3 minutes to be ready (Power LED should be fixed when finish booting). In order to prevent unauthorized SSH router will launch OpenWRT. Use the "passwd" command to set up a new password There is no root password defined on this device! Detected 1 available secondary CPU(s)īusyBox v1.35.0 ( 10:09:10 UTC) built-in shell (ash) Initrd not found or empty - disabling initrd Linux version 5.10.155 (mips-openwrt-linux-musl Image Type: MIPS Linux Kernel Image (lzma compressed) # Booting kernel from Legacy Image at 81000000. Tftpboot openwrt-lantiq-xrx200-arcadyan_vrv9510kwac23-initramfs-kernel.imgīootm $fileaddr U-Boot # tftpboot openwrt-lantiq-xrx200-arcadyan_vrv9510kwac23-initramfs-kernel.binįilename 'openwrt-lantiq-xrx200-arcadyan_vrv9510kwac23-initramfs-kernel.bin'. Run the following commands to upload the image to the router and launch it in RAM You can find it on the back of your router.ĭownload the openwrt-lantiq-xrx200-arcadyan_vrv9510kwac23-initramfs-kernel.img image and place it in your TFTP server directory. Replace XX:XX:XX:XX:XX:XX with your custom MAC. Set the MAC Address with the following commands. *** Warning - bad CRC, using default environment As there is no firmware installed, you will get an error which is completly normal. Restart the router, you will see the new bootloader installed. Nand erase 0 $filesize & nand write $fileaddr 0 $filesize NAND write: device 0 offset 0x0, size 0x569a8 Nand erase.chip NAND erase.chip: device 0 whole chipįlash the bootloader into the nand by typing Type the following code to full erase the NAND: Upload this image to the router by typing Since the OEM brnboot bootloader is useless for us, we will replace this bootloader with U-Boot, so we will be able to control the boot configuration of our router.ĭownload the image and place it in your TFTP server directory. I recomend performing a second backup, then compare the files to see if the backup is correct. When the process is finished, you will have a file named arcadyan-VRV9510KWAC23-backup.bin. Ltq_phy: addr 5, link 0, speed 10, duplex 0 Ltq_phy: addr 19, link 0, speed 100, duplex 0 Ltq_phy: addr 17, link 0, speed 100, duplex 0 Ltq_phy: addr 1, link 0, speed 10, duplex 0 Ltq_phy: addr 0, link 1, speed 100, duplex 1 NAND read: device 0 offset 0x0, size 0x7f80000 Once setup is done, run this two commands on your router: Make sure you give writing permissions to the server so the backup can be stored on your machine. You can use TFTP64 if you are using Windows or tftpd-hpa if you are using Linux. You will need to setup a TFTP server to get the backup. Set a static IP address “192.168.1.2” and gateway “192.168.1.1” for your Ethernet adapter. Arcadyan has not provided a OEM firmware for this device, so if you want to go back to the OEM firmware, performing a backup is mandatory.Ĭonnect a ethernet cable in the GE4 port of the router (the closest one to the phone ports) and your computer.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |